VietSteelUSA

Deck lines

Deck roll forming lines

Steel deck lines, from a single-purpose line for one profile to universal high-speed rafted lines.

Request a quote Call Kerry

Watch a Vietsteel floor deck line run on YouTube

The range

Three ways to build a deck line.

The line is specified around the deck profiles you run and the output you need.

  • One profile

    Single-purpose lines

    One deck profile on its own tooling. The simplest way to run a profile you make every day.

  • Profiles on rafts

    Cassette lines

    The forming stations are built into cassette blocks, or rafts, that ride on rails. A second set of blocks can stand beside the first, so the line is not tied to one product.

  • Several profiles, high output

    Universal high-speed rafted lines

    The top of the range, for plants that run several deck profiles at volume. Each profile has its own raft set, and the line is specified for speed.

Example configuration

B-deck cassette line.

A cassette line for B deck, as Vietsteel specifies it for a US plant. Drawings and figures are from the line specification.

The whole line, 138 ft long. Uncoiler and sheet cutting inside one fence, the cassette roll former under its covers, and the stacker inside a second fence. The inset shows a light curtain post.
Deck
1½ in B deck36 in cover, 6 in pitch
Coil
22–16 gaASTM A653, SS Grade 50
Forming speed
82–98 ft/min40 stations in four blocks
Power supply
480 V3-phase, 60 Hz
  • Cassette roll former. Four cassette blocks on a chassis that runs on floor rails.
  • The four blocks. 40 forming stations in all, under sliding clear covers.
  • Sheet cutting machine. Hands-free table, straightening rolls and a hydraulic cut, ahead of the former.
  • Uncoiler with coil car. Six tons, with a hydraulic snubber arm.
  • Automatic stacker. A 40 ft table fed by a belt conveyor, with seven chain conveyors to move packs out.
  • Stacker in section. Roller arms open to drop each sheet onto the pack. Head and side push square it.

Specification

Technical data.

The B-deck cassette line as specified. Where the specification gives both units, the US figure is its own.

Deck profile
B deck: 36 in cover, 6 in pitch, 1½ in deep, with embossed webs
Coil
49 in wide, 22 to 16 gauge, galvanized to ASTM A653, SS Grade 50 (50 ksi minimum yield)
Uncoiler
6-ton automatic uncoiler with coil car. 20 in bore, coils up to 47.2 in outside diameter
Cut to length
Before forming, on a hydraulic sheet cutting machine with a straightening unit, fed by a hands-free table. Length tolerance ±0.039 in
Edge slitting
One slitter knife station with a side re-coiler. Slit width 0.25–3.15 in
Roll forming
40 forming stations in four cassette blocks, each block driven by its own 20 hp motor and gearbox
Forming speed
82–98 ft/min
Cassette blocks
The blocks ride on floor rails and are moved by two rail motors. The layout marks a position for a second roll forming set beside the first.
Stacking
Automatic stacker with a 40 ft table and a 6-second cycle. Packs 9.8–40 ft long, up to 8,800 lb
Control
PC control system. Job lists load from .nc1 files or Excel production orders. Production history is kept for more than three years, the line reports running, stopped and fault time to the office, and it can be reached over the internet for fault-finding.
Guarding
Fixed safety fences with light curtains around the uncoiler and stacker areas. Sliding covers of clear polycarbonate over the forming blocks.
Power
480 V, 3-phase, 60 Hz. About 138 hp installed across the line
Line size
138 ft long, 33 ft wide and 7.2 ft high. About 106,000 lb
Components
PLC Siemens, Delta or INVT; encoders Kübler, Omron or Autonics; motors ABB or Toshiba; hydraulics Yuken. Rolls in SCM440 steel, heat treated and chrome plated. Cutting dies in SKD11 tool steel.

Line flow

Coil in, packs out.

The sheet is cut to length before it is formed, so the roll former has no cut-off. Lengths are each station’s share of the line.

  1. Uncoiler with coil car6 ft
  2. Hands-free table10 ft
  3. Sheet cutting10 ft
  4. Entry guide
  5. Roll forming, four blocks58 ft
  6. Belt conveyor10 ft
  7. Automatic stacker40 ft
The B deck sheet as drawn in the specification, with embossed webs.
Deck sheets off a Vietsteel floor deck line.

Floor deck

Vietsteel’s published floor deck line.

A conventional floor deck line, with a hydraulic cut-off after forming. Figures are Vietsteel’s published specification.

The exit end of a Vietsteel floor deck line.
A Vietsteel decking line with its run-out table.
Material thickness
0.028–0.063 in
Yield strength
51–80 ksi
Coil width
47.2–49.2 in
Forming speed
72–82 ft/min
Forming stations
32 to 42
Cut-off
Hydraulic, after forming
Control
PLC with touch-screen HMI
Main drive
30–60 hp
Line length
39–72 ft

Contact

Send the deck profiles you run.

Profile drawings, gauge and grade range, coil width and the output you need. Kerry will come back with the configuration that fits and a quote.

Request a quote See the purlin lines

US sales contact
Kerry Hayes
General inquiries
enquiry@vietsteelusa.com